• $1,600.00 S&H

    Samsung SM 2MM Pitch Feeder Finger

    For Samsung SM 2MM Pitch Feeders

    8 Feeder Fingers per case

     

    The SM 0402 Cut Tape Feeder Finger is designed to work with Samsung’s SM 2mm Pitch Pneumatic Feeders to improve the feeder’s efficiency and significantly reduce feeder setup and change over time. The operator now can load a strip of tape as short as three inches or a full reel in less than five seconds. No tape leader is required, and little to no parts are lost on the initial feed of tape.

     

    Experience ultimate convenience while saving time with the SM 0402 Cut Tape Feeder Finger.

     

     

    Key benefits:

    • Attaches easily to your existing feeder
    • Handles cut tape as short as three inches
    • Eliminates splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0201 / 0402
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper only
    Full Reels or Cut Tape Yes
    Package Weight 7 lbs
    Dimensions 14 x 12 x 6 in

    For Samsung SM 2MM Pitch Feeders
    8 Feeder Fingers per case

  • $1,600.00 S&H

    IPulse F3 Feeder Finger

    For I-Pulse F3 Feeders

    8 Feeder Fingers per case

     

    The IPE Cut Tape Feeder Finger Solution is designed to work with the iPulse F3 Electronic Feeders to improve the feeder’s efficiency and significantly reduce feeder setup and change over time. The Feeder Finger coupled with the advantages of the electric motor upgrade the F3 Feeder to autoload status. Merely push the component tape into the feeder and place it onto the pick and place. The tape leader is no longer required, and the cover tape collection process is eliminated. Your feeders can now be loaded and unloaded in seconds, reducing production setup time by as much as fifty percent.

     

    Key benefits:

    • Attaches easily to your existing feeder
    • Handles cut tape as short as three inches
    • Eliminates splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0201 / 1206
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper Tape & Heat Sealed Plastic Tape
    Full Reels or Cut Tape Yes
    Package Weight 7 lbs
    Dimensions 14 x 12 x 6 in

     

    For I-Pulse F3 Feeders
    8 Feeder Fingers per case

  • $18.00 S&H

    Tape Push Tool

    The Tape Push Tool is used to advance the component tape onto the sprocket wheel. This tool is recommended for use with all tapes.

  • Essemtec Feeder Finger

    Essemtec Feeder Finger

    The Essemtec Feeder Finger Solution is in Development.

     

    Weight 7 lbs
    Dimensions 14 x 12 x 6 in
  • Juki RF08FF Feeder Finger

    Juki Feeder Finger products are distributed exclusively by Juki Automation Systems, Inc.

     

    Contact your Juki representative for more information.

     

    Weight 7 lbs
    Dimensions 14 x 12 x 6 in
  • Juki EF08FF Feeder Finger

    Juki EF08FF Feeder Finger

    Juki Feeder Finger products are distributed exclusively by Juki Automation Systems, Inc.

     

    Contact your Juki representative for more information.

     

    Weight 7 lbs
    Dimensions 14 x 12 x 6 in
  • Juki CF08FF Feeder Finger

    Juki CF08FF Feeder Finger

    Juki Feeder Finger products are distributed exclusively by Juki Automation Systems, Inc.

     

    Contact your Juki representative for more information.

     

    Weight 7 lbs
    Dimensions 14 x 12 x 6 in
  • Juki AF05FF Feeder Finger

    Juki AF05FF Feeder Finger

    Juki Feeder Finger products are distributed exclusively by Juki Automation Systems, Inc.

     

    Contact your Juki representative for more information.

     

    Weight 7 lbs
    Dimensions 14 x 12 x 6 in
  • $75.00 S&H

    Tape Dent Tool

    The Tape Dent Tool is used to crimp the component tape before inserting it into the Feeder Finger. The moon shaped dent allows the blade to quickly penetrate and separate the cover tape from the component tape.