• $200.00 S&H

    Yamaha SS / YS / ZS Feeder Finger (Case of 10)

    For Yamaha SS / YS & ZS Feeders

    10 Feeder Fingers per case

     

    The YS / SS and ZS Feeder Fingers are designed to work with the Yamaha Electronic Feeders to improve feeder efficiency and increase production capacity. The key features and benefits allow an operator to load tape strips as short 3 inches or a full reel in 5 seconds with zero components loss. Eliminating the cover tape collection process eliminates feeder jams during production improving machine utilization and throughput.

     

    Key benefits:

    • Attaches easily to your existing feeder
    • Handles cut-tape as short as 3″ /76.2mm
    • Eliminates splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0201 / 1206
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper Tape & Heat Sealed Plastic Tapes
    Full Reel & Cut Tape Yes

     

    Package Weight 3 lbs
    Dimensions 14 x 12 x 6 in

     

    For Yamaha SS / YS & ZS Feeders
    10 Feeder Fingers per case

  • $200.00 S&H

    Samsung SM Feeder Finger (Case of 8)

    For Samsung SM Pneumatic Feeders

    8 Feeder Fingers per case

     

    The SM Feeder Finger is designed to work with the Samsung SM Pneumatic Feeder to improve feeder efficiency and significantly reduce production setup and change over time. The key features and benefits allow the operator to load tape strips as short as three inches or the full reel in 5 seconds with zero component loss. Eliminating the cover tape collection process eliminates feeder jams during production improving machine utilization and throughput.

     

     

    Key benefits:

    • Attaches easily to your existing feeder
    • Handles cut-tape as short as 3″ / 76.2mm
    • Eliminates splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0603 / 1206
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper Tape only
    Full Reels or Cut Tape Yes
    Package Weight 3 lbs
    Dimensions 14 x 12 x 6 in

     

    For Samsung SM Feeders
    8 Feeder Fingers per case

  • $200.00 S&H

    Samsung CP Feeder Finger (Case of 8)

    For Samsung CP Feeders

    8 Feeder Fingers per case

     

    The CP Cut Tape Feeder Finger Solution is designed to work with Samsung’s legacy CP Feeders to make feeding component tape easier than ever. Merely push the tape into the Feeder Finger and index the feeder one time. The first component is ready to be picked. No tape leader is required, and the cover tape collection process is eliminated entirely. By simplifying the feeder loading and unloading process, feeder setup and changeover times are significantly reduced.

     

    At the end of the day, this means significantly higher productivity.

     

    Key benefits:

    • Attaches easily to your existing feeder
    • Handles cut tape as short as three inches
    • Eliminates splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0402 / 1206
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper Tape only
    Full Reel or Cut Tape Yes
    Package Weight 7 lbs
    Dimensions 14 x 12 x 6 in

     

     

    For Samsung CP Feeders
    8 Feeder Fingers per case

  • $200.00 S&H

    IPulse F3 Feeder Finger (Case of 10)

    For I-Pulse F3 Feeders

    10 Feeder Fingers per case

     

    The F3 Feeder Finger is designed to work with the iPulse F3 Electronic Feeders to improve feeder efficiency and significantly reduce production setup and change over time. The Feeder Finger coupled with the F3 Feeder allows the operator to load tape strips as short as 3 inches or the full reel in 5 seconds with zero component loss. Eliminating the cover tape collection process eliminates feeder jams during production improving machine utilization and throughput.

     

    Key benefits:

    • Attaches easily to your existing feeder
    • Handles cut-tape as short as 3″ / 76.2mm
    • Eliminates splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0201 / 1206
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper Tape & Heat Sealed Plastic Tape
    Full Reels or Cut Tape Yes

     

    Package Weight 3 lbs
    Dimensions 14 x 12 x 6 in

     

    For I-Pulse F3 Feeders
    10 Feeder Fingers per case

  • $200.00 S&H

    Samsung SM 2MM Pitch Feeder Finger (Case of 8)

    For Samsung SM 2MM Pitch Feeders

    8 Feeder Fingers per case

     

    The SM 0402 Feeder Finger is designed to work with the Samsung 2mm Pitch Pneumatic Feeders to improve feeder efficiency and significantly reduce feeder setup and change over time. The key features and benefits allow the operator to load tape strips as short as three inches or the full reel in 5 seconds with zero component loss. Eliminating the cover tape collection process eliminates feeder jams during production improving machine utilization and throughput.

     

     

    Key benefits:

    • Attaches easily to your existing feeder
    • Handles cut-tape as short as 3″ / 76.2mm
    • Eliminates splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0201 / 0402
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper only
    Full Reels or Cut Tape Yes
    Package Weight  3 lbs
    Dimensions 14 x 12 x 6 in

    For Samsung SM 2MM Pitch Feeders
    8 Feeder Fingers per case

  • Samsung SME Feeder Finger
    $200.00

    Samsung SME Feeder Finger (Case of 8)

    For Samsung SME Electric Feeders

    8 Feeder Fingers per case

     

    The SME Feeder Finger is designed to work with the Samsung SME Electric Feeder to improve feeder efficiency and significantly reduce production setup and change over time. The key features and benefits allow the operator to load tape strips as short as three inches or the full reel in 5 seconds with zero component loss during the initial feeder of tape. Eliminating the cover tape collection process eliminates feeder jams during production improving machine utilization and throughput.

     

    Key benefits:

    • Attaches easily to your existing feeder
    • Handles cut-tape as short as three inches
    • Eliminates splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0201 / 1206
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper Tape only
    Full Reels or Cut Tape Yes
    Weight 3 lbs
    Dimensions 14 x 12 x 6 in
  • $200.00 S&H

    Juki RF08FF Feeder Finger (Case of 10)

    For Juki RF08AS Feeders

    10 Feeder Fingers per case

     

    The RF08 Feeder Finger requires a firmware upgrade from Juki Automation Systems, Inc.

     

    The RF08 Feeder Finger was designed in conjunction with Juki Automation Systems to work with the New RS1 pick and place machine. The Feeder Finger coupled with the new RF08AS electronic feeder adds key features and benefits that improve machine utilization and throughput. An unskilled operator can load tape strips as short as three inches or a full reel without a cover tape leader or tape splicing. The cover tape collection process and cover tape feeder jams are eliminated. The operator merely pushes the component tape into the feeder and places it onto the pick and place or feeder cart improving production setup time by 50%.

     

    Key benefits:

    • Attaches easily to your existing feeder
    • Handles cut-tape as short as 3″ / 76.2mm
    • Eliminates tape splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0201 / 1206
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper Tape only
    Full Reels or Cut Tape Yes

     

    Package Weight 3 lbs
    Dimensions 14 x 12 x 6 in

     

    For Juki RF08AS Feeders
    10 Feeder Fingers per case

  • Juki EF08FF Feeder Finger
    $235.00 S&H

    Juki EF08FF Feeder Finger (Case of 8)

    For Juki EF08HSR Feeders

    8 Feeder Fingers per case

     

    The EF08 Feeder Finger requires installation by a feeder technician and a firmware upgrade from Juki Automation Systems, Inc.

     

     

    The EF08 Feeder Finger was designed in conjunction with Juki Automation Systems to work with the EF08HSR electronic feeder (black handle). The Feeder Finger, coupled with the EF08HSR feeder, adds key features and benefits that enhance machine utilization and throughput. An unskilled operator can load tape strips as short as three inches or a full reel without a cover tape leader or tape splicing. The cover tape collection process and cover tape feeder jams are eliminated, reducing feeder preparation time by 50%. The operator merely pushes the component tape into the feeder and places it onto the pick and place or feeder cart.

     

    Key benefits:

    • Attaches to existing feeder Technician Installation Required
    • Handles tape strips as short as 3″/ 76.2mm
    • Eliminates splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0201 / 1206
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper Tape only
    Full Reels or Cut Tape Yes

     

    Package Weight 3 lbs
    Dimensions 14 x 12 x 6 in

     

    For Juki EF08HSR Feeders
    8 Feeder Fingers per case

  • Juki CF08FF Feeder Finger
    $235.00 S&H

    Juki CF08FF Feeder Finger (Case of 8)

    Works with Juki CF081ER, CF03HPR & CF05HPR Feeders

    8 Feeder Fingers per case

     

     

    The CF08 Feeder Finger was designed in conjunction with Juki Automation Systems to work with the CF081ER 4mm pitch mechanical feeder (blue handle) and the CF03HPR & CF05HPR 2mm pitch feeders. The Feeder Finger, coupled with these feeders, increases production capacity by 150% by reducing production setup and change over time.  The key features and benefits allow the operator to load tape strips as short as three inches or the full reel in 5 seconds with zero component loss. Eliminating the cover tape collection process eliminates feeder jams during production improving machine utilization and throughput.  Removing the mechanical mechanism for collecting the cover tape reduces feeder maintenance costs significantly.

     

     

    Key benefits:

    • Attaches easily to your existing feeder
    • Handles tape strips as short as 3″ / 76.2mm
    • Eliminates splicing
    • Loads in less than 5 seconds
    • Eliminates cover tape jams
    • Reduces setup time by fifty-percent
    Cut Tape Feeder Finger Specification
    Typical components 0201 / 1206
    Tape Width 8 mm
    Tape depth (feeder type) 2.5 mm (8 mm)
    Tape material Paper Tape only
    Full Reels or Cut Tape Yes
    Package Weight 3 lbs
    Dimensions 14 x 12 x 6 in

     

    Works With Juki  Model CF081ER & CF03HPR & CF05HPR Feeders
    8 Feeder Fingers per case